How To Winterize An Outboard Motor 2 Stroke

How to Prep Your Outboard Motor for Winter Storage. Avoid Seafoam and other additives unless youre experiencing a problem that they are designed to fix.

Winterizing Your Outboard Motor West Marine

With the engine running spray a small amount of fogging oil into the intake.

How to winterize an outboard motor 2 stroke. This adds the needed layer of oil residue onto all the interior parts. Turn on the water and start the engine. Remove strip and clean the carburettor.

Using an outboard flusher or earmuffs as some call them put them over the raw water intake of the engine and connect a hose. Prior to winterizing the engine its a good idea to give the boat a good cleaning inside and out power wash the bottom and put a coat of wax on fiberglass hulls. However you should do it regardless of how long its been before storing your outboard because harmful contaminants in the used oil can corrode the inside of.

You can do this on an engine stand or sawhorse at the same time youre flushing the engine. Hook up a garden hose to a motor flush attachment which will cover the water intake on the lower unit of the motor. For older two-stroke motors you use canned fogging oil and spray it into the carburetors just as the motor idles out of fuel.

The engine will want to die but keep it running by opening the throttle. For direct-fuel-injected DFI two-stroke engines such as Mercury OptiMax Yamaha HPDI and Evinrude E-TEC models instead of using fogging oil squirt 1 ounce of DFI outboard oil into each cylinder through the spark plug hole. Next and this is very important.

Lower Unit Oil Change Mercury recommends the gearcase lube be changed every 100 hours or once per year. Check the spark plug. Your outboard was designed to run on pure gasoline and good 2 stroke oil without snake oils turnip juice hair tonics or any other.

Remove the gearbox to check the water pump. Remove the engine cover and find the carburetors air intake port. This step-by-step guide takes you through a service of a small 2-stroke outboard.

The first will be found near the bottom of the skeg you unscrew this one first and oil will begin to immediately pour out. However you should do it regardless of how long its been before storing your outboard because harmful contaminants in the used oil can corrode the inside of. Make sure to place a drain pan underneath the unit before you begin to take any screws out.

Check the recoil starter. For direct fuel injected DFI two-stroke engines such as Mercury OptiMax models instead of using fogging oil squirt one ounce of DFI outboard oil into each cylinder through the spark plug hole. There is no need to change plugs if it runs fine but always have a spare set.

Change oil filter. If white smoke comes out of the exhaust youre doing it right. Get supplies for your 2-stroke outboard winterization here.

On smaller engines with only one. Httpbitlytwo-stroke-outboard-winterization-kitWinterizing a 2-stroke outboard motor puts an. Winterizing a 2-Stroke Outboard.

Continue to fog the engine until it dies. You want to make absolutely sure that every drop of water is out of the motor. A small oil can with a long flexible neck works well for this task.

Drain the old fuel. This will help get rid of any sediment collecting within the system. How to DIY Winterizing a 2 Stroke Outboard Engine Mercury Force 120HP.

Lower Unit Oil Change Mercury recommends the gearcase lube be changed every 100 hours or once per year. We take you through the steps on how we prepare our bowrider Starcraft Boat with Me. Hook up the water again and run the motor for a good 10-15 minutes to work the stabilized fuel through the motor.

Another important factor when winterizing your outboard motor is to flush it with water. Flush the engine with fresh water. Winterizing a 2-Stroke Outboard.

Tilt the motor all the way up and all the way down. As a precursor to the winterizing process mixing fuel stabilizer into the last tank of fuel for the final excursion of the season allows the fuel stabilizer to circulate throughout the motor coating the various fuel system surfaces with the stabilizer. Now there will be 2 screws you will need to unscrew in order to drain the oil.

Winterizing your Mercury outboard is the last step before sending the motor into hibernation at the end of the season. Here are the steps. How to service a 2-stroke outboard engine Do it yourself.

How To Winterize A 2 Stroke Outboard Motor Boats Net