How To Install Shower Drains

Fix your shower drains in either of these sites. After the shower base is set lubricate the gasket with plumbers soap and slide it into place between the drain body and the pipe.

Shower Plumbing Tips That Can Save You A Fortune Plumbing Tips Shower Drain Installation Shower Plumbing Shower Drain

2 Drain Pipe should be centered in a hole approximately 5 diameter in the flooring.

How to install shower drains. Tighten the compression nut inside the drain body with a screwdriver to seal the connection then snap the strainer into place. Install the shower base and push the gasket into the drain pipe and tighten. Tail-piece inserting Secondly you need to insert the tail-piece at the mouth of the waste taking drain.

The Drain body is inserted from the top side and pressed firmly into place so that the Silicone Adhesive forms an even seal. Installation Position Of Drains When we install the drains we can install the drain and set the position of drains first floor tiles slope to the floor we can place the ceramic in the position and set ceramic in the center of drain the diagonal is straight that has drained away water then is in the middle of drain. Although this stage is quite straightforward youll probably need an extra pair of hands to align the shower drain over the drain pipe.

While installing your linear shower drain we have identified ideal locations. The first step of installing the compression-style shower drain is to cut the waste-pipe in a way that it remains ¾ -1 inch below the surface area. There are usually 2 or 3 screws that hold the existing drain in place on the floor of your shower.

Installing Your Shower Drain. Thread the mounting nut onto the tailpiece and tighten it down with channel-lock pliers. In order to expose the drainage pipes leading into the shower drain and install the necessary replacements requires that cement over and around the area be.

It is necessary to prepare all the things before starting installation. After youve picked out your shower drain you should be ready to install the new one. Installation is one of the most important parts of the shower drain installation.

Cover the flange on the shower drain fitting with plumbers putty and insert the tailpiece of the drain into the opening and tighten. Installing the Shower Drain Youll need to connect the shower drain to the drain pipes with nuts. Remove the screws with a screwdriver and pull up on the drain cap.

It is recommended to prepare the area where you are going to install the shower drain including surrounding walls and plumbing. The WingTite Drain simply slips over the drainpipe and an O-ring seals it. Apply a bead of silicone caulk around the top flange of the shower drain opening then insert the drain assembly into the opening.

Install Drain Body in Shower Base before the Base is put in place on the floor. Before the installation its very important to turn off the electricity and gas supply of your bathroom so that it wont be damaged. If your home is built on a concrete slab be prepared to break into the cement floor to properly install your shower drain.

To avoid leakage your shower drain and the drain pipes should be of the same size. Then pull up on the drain. At the edge of a wall along with the doorway or even somewhere at the center.

A stainless cover fits over the top although decorator finishes are also available. Apply 100 percent silicone sealant to underside of the drain flange to seal to the shower base. Required Tools for this shower drain installation Project.

The top of the Pipe should be no higher than and no more than 18 lower than the top surface of the floor on which the base will be set. The drain should come up to ¾ to 1 inch below the lip of the shower drain. The first step is to remove the old drain.

Put the rubber sealing washer and cardboard friction washer over the drain assembly tailpiece from under the shower base. You now should expose your PVC piping. If youre planning on replacing any of the piping below the drain make sure to choose a piece of PVC pipe that fits.

Locating The Waste Drain Piping System Make sure you linear drain is. Make a mark on the pipe at the appropriate height remove your shower base and cut your pipe. Heres how to quickly install a compression shower drain.

Put silicone caulk or plumbers putty on. Leave the existing drainpipe intact. Remove the gasket before the shower base is set.

Put your shower base in but do not install it yet.

Easy Drain Aqua Brilliant Shower Drain Installation English Youtube